U2693 Sunbeam-talbot 90 OBD Code

OBD/2 U2693 error code description and symptoms.

Brake Switch Circuit Input Malfunction Indicates PCM did not receive a brake pedal position (BPP) input. Open or short in BPP circuit Open or short in stoplamp circuits Damaged PCM Malfunction in module(s) connected to BPP circuit. (Rear Electronic Module [REM] Windstar and LS6/LS8 or Lighting Control Module (LCM) Continental and Town Car. Damaged brake switch Misadjusted brake switch Check for proper function of stoplamps.

Gear changes are accomplished by a command from the TCM to energize the clutch actuator to release the clutch; after which various actuators inside the transmission disengage the current gear, and depending on current operating conditions, engage the next higher or lower gear ratio. All of this happens much faster than a human driver could change gears, and in most applications, gear changes are as smooth and seamless as on any fully automatic transmission.

U2693 Sunbeam-talbot 90 Error Code Repair Process :

When you turn on the ignition, the Service Engine Soon or Check Engine U2693 light should flash briefly, indicating that the OBD system is ready to scan your vehicle for any malfunctions. After this brief flash, the light should stay off while you drive as long as no problems are detected. If scp (j1850) invalid or missing data for charging system so, you'll be glad to know that your vehicle is equipped with an early warning system that could save you time, money, and fuel in addition to helping protect the scp (j1850) invalid or missing data for charging system.

Difficulty Level (Expert)

Repair Time (35 Min.)

Cost Prediction : $ 30-110

Common Causes of Sunbeam-talbot 90 U2693 OBD2 Code

A common cause of code U2693 is the failure of SCP (J1850) Invalid or Missing Data for Charging System, but there are several other possible causes as well, such as ;

• Failures of clutch motion/travel sensors.
• EVAP system hose leaking
• Fuel injectors harness is open or shorted
• Ignition misfiring

U2693 is a kind of Network Trouble Code U-code indicates that engine communication errors and shows lost communication with engine parts.U-Codes are fairly straight forward, given all of the articles and technical publications that have been written regarding these problematic codes. In most cases, it just comes down to identifying the module that isn't communicating with the other modules on the CAN bus line for whatever reason.

U2693 code for other Sunbeam-talbot cars

You can view according U2693 DTC for your car model. We selected several models to see obd2 solutions click and view it.

• U2693 Sunbeam 10
• U2693 Sunbeam 12
• U2693 Sunbeam 14
• U2693 Sunbeam 20
• U2693 Sunbeam 24
• U2693 Sunbeam 2-litres
• U2693 Sunbeam 3
• U2693 Sunbeam 30
• U2693 Sunbeam 3-litre
• U2693 Sunbeam 3-litres
• U2693 Sunbeam 4-litres
• U2693 Sunbeam Alpine
• U2693 Sunbeam Chamois
• U2693 Sunbeam Imp
• U2693 Sunbeam Rapier
• U2693 Sunbeam Tiger
• U2693 Sunbeam Venezia
• U2693 Sunbeam Vogue
• U2693 Sunbeam-talbot 4-litre
• U2693 Sunbeam-talbot 80
• U2693 Sunbeam-talbot Alpine
• U2693 Sunbeam-talbot Mk Iii
• U2693 Sunbeam-talbot Rapier
• U2693 Sunbeam-talbot Tiger

Engine OBD 2 Codes website is a freeware resource center for engine trouble codes.

About Us | Contact | Privacy

Copyright 2017 © All rights reserved