P2347 Simca Tufao OBD Code

OBD/2 P2347 error code description and symptoms.

The Transmission Fluid Pressure Switch allows the engine's control module (PCM) or Transmission Control Module (TCM) to use hydraulic fluid to engage the clutches in the transmission to allow for smoother shifting while driving. If the PCM or TCM detects an issue with the hydraulic clutch or the pressure switch, the PCM or TCM will set code P2347

In most cases, the TCM is integrated into a single housing with the PCM. Nevertheless, the section of the module which controls (automatic) transmission function may be powered up separately. In any case, the TCM is typically powered using switched (only present with the ignition switch in the ON, start, or run position) voltage. This circuit is normally equipped with a fuse, fusible link, and/or a relay. Frequently, the PCM and TCM are powered using the same relay albeit by separate circuits. Access to a reliable vehicle information source will yield necessary details of the TCM power circuit for the specific vehicle in question.

P2347 Simca Tufao Error Code Repair Process :

If your vehicle failed a P2347 test and the P2347 Check Engine Light is NOT on, chances are you have a problem with the OBDII system, a burned out MIL lamp, or a faulty catalytic converter. The converter is essentially an afterburner that cleans up the exhaust after it exits the engine. The OBDII system uses p2347 cylinder 12 above knock threshold a ownstream oxygen sensor to monitor the efficiency of the converter, and it should detect a drop in converter efficiency if the converter has been contaminated or is failing (ignition misfiring, leaky exhaust valves, and oil burning can all damage the converter). What you want to look p2347 cylinder 12 above knock threshold: Any conditions that might cause ignition misfire, an overly rich or lean fuel condition, or loss of compression. Use your OBD Express DIY to look at the oxygen sensor outputs, coolant temperature, airflow, calculated engine load, and inlet air temperature.

Difficulty Level (Soso)

Repair Time (30 Min.)

Cost Prediction : $ 70-220

Common Causes of Simca Tufao P2347 OBD2 Code

A common cause of code P2347 is the failure of P2347 Cylinder 12 Above Knock Threshold, but there are several other possible causes as well, such as ;

• Continuous oil flow to the VCT piston chamber
• Faulty front heated oxygen sensor
• Incorrect fuel filler cap used
• Variable Camshaft Timing (VCT) position circuit poor electrical connection

P2347 is a kind of Powertrain Trouble Code Powertrain of a modern automobile, comprising engine (with exhaust system), transmission, drive shaft, suspension and the wheels. In a motor vehicle, the term powertrain or powerplant describes the main components that generate power and deliver it to the road surface, water, or air.

P2347 code for other Simca cars

You can view according P2347 DTC for your car model. We selected several models to see obd2 solutions click and view it.

• P2347 Simca 1000
• P2347 Simca 11
• P2347 Simca 1100
• P2347 Simca 1200
• P2347 Simca 1300
• P2347 Simca 1301
• P2347 Simca 1307
• P2347 Simca 1308
• P2347 Simca 1309
• P2347 Simca 1500
• P2347 Simca 1501
• P2347 Simca 2 Litres
• P2347 Simca 5
• P2347 Simca 6
• P2347 Simca 8
• P2347 Simca Ariane
• P2347 Simca Aronde
• P2347 Simca Horizon
• P2347 Simca Montlhery
• P2347 Simca Oceane
• P2347 Simca Plein
• P2347 Simca Plein Ceil
• P2347 Simca Type 11
• P2347 Simca Vedette
• P2347 Simca Vedette Beaulieu
• P2347 Simca Vedette Marly
• P2347 Simca Vedette Versailles

Engine OBD 2 Codes website is a freeware resource center for engine trouble codes.

About Us | Contact | Privacy

Copyright 2017 © All rights reserved