P2088 Daimler Majestic OBD Code

OBD/2 P2088 error code description and symptoms.

Engine Coolant Temperature (ECT) Circuit High Input Indicates the sensor signal is greater than Self-Test maximum. The ECT sensor maximum is 4.6 volts or -50 C (-58 F). Note on some vehicles that are not equipped with an ECT sensor, CHT can be used and can set this DTC. Open circuit in harness Sensor signal short to power Damaged PCM Improper harness connection Damaged sensor ECT V PID reading greater than 4.6 volts with key ON and engine OFF or during any engine operating mode indicates a hard fault.

Circuit High Input codes like P2088 are mostly caused by defective alternators that develop excessive voltages, although there may be other causes as well, such as short circuits that 'leak' current into a particular system from other, unrelated systems that work on higher voltages. Note that in the case of short circuits that leak power into a control circuit, there is likely to be other, seemingly unrelated trouble codes present along with the code(s) being investigated. Diagnosing a 'high input' code will always involve a thorough testing of the charging system as a first step, followed by measures to isolate the system from all other possible sources of power during resistance, continuity, and reference voltage tests.

P2088 Daimler Majestic Error Code Repair Process :

If your p2088 a camshaft position actuator control circuit low bank 1 check engine light is illuminated, it's best to take it in for diagnostic testing, which can feel like a hassle. Because while the lights vary in appearance from vehicle to vehicle, all have the same basic meaning: There's a problem with the car's emissions system. The on-board diagnostics system P2088 and engine control unit are in charge of monitoring a bunch of different p2088 a camshaft position actuator control circuit low bank 1, and if they get a reading that's a little out of whack, up pops the check engine light.

Difficulty Level (Easy)

Repair Time (45 Min.)

Cost Prediction : $ 80-120

Common Causes of Daimler Majestic P2088 OBD2 Code

A common cause of code P2088 is the failure of P2088 A Camshaft Position Actuator Control Circuit Low Bank 1, but there are several other possible causes as well, such as ;

• Engine Control Module (ECM)
• Erratic camshaft position due to low oil pressure
• Faulty select solenoid
• Open or short in the VCT circuit

P2088 is a kind of Powertrain Trouble Code Powertrain of a modern automobile, comprising engine (with exhaust system), transmission, drive shaft, suspension and the wheels. In a motor vehicle, the term powertrain or powerplant describes the main components that generate power and deliver it to the road surface, water, or air.

P2088 code for other Daimler cars

You can view according P2088 DTC for your car model. We selected several models to see obd2 solutions click and view it.

• P2088 Daimler 2.5-litre
• P2088 Daimler 24
• P2088 Daimler 3-litre
• P2088 Daimler 4.2
• P2088 Daimler 4.5-litre
• P2088 Daimler 4-litre
• P2088 Daimler Conquest
• P2088 Daimler Daimler
• P2088 Daimler Db
• P2088 Daimler De
• P2088 Daimler Dk
• P2088 Daimler Double Six
• P2088 Daimler Light
• P2088 Daimler Limousine
• P2088 Daimler One-o-four
• P2088 Daimler Sp
• P2088 Daimler Super

Engine OBD 2 Codes website is a freeware resource center for engine trouble codes.

About Us | Contact | Privacy

Copyright 2017 © All rights reserved