P0C03 Bristol 404 OBD Code

OBD/2 P0C03 error code description and symptoms.

EGR Flow Insufficient Detected The EGR system is monitored during steady state driving conditions while the EGR is commanded on.
The test fails when the signal from the DPF EGR sensor indicates that EGR flow is less than the desired minimum. Vacuum supply EGR valve stuck closed EGR valve leaks vacuum EGR flow path restricted EGRVR circuit shorted to PWR VREF open to D.P.F. EGR sensor D.P.F. EGR sensor downstream hose off or plugged EGRVR circuit open to PCM VPWR open to EGRVR solenoid D.P.F. EGR sensor hoses both off D.P.F. EGR sensor hoses reversed Damaged EGR orifice tube Damaged EGRVR solenoid Damaged PCM Perform KOER self-test and look for DTC P0C03 as an indication of a hard fault.

To check for an open circuit, trace along the length of the transmission control circuit, checking for breaks in the wiring. Repair any broken wiring and make sure all connectors are fully seated and locked.Pay close attention to connectors, looking for corrosion, bent or broken pins, or moisture in the connector. Repair any connector issues even if they are not specifically part of the transmission control circuit as they may serve a function in providing power to the transmission control circuit.

P0C03 Bristol 404 Error Code Repair Process :

If your aux heater start counter overrun/system locked (same as below ?) check engine light is illuminated, it's best to take it in for diagnostic testing, which can feel like a hassle. Because while the lights vary in appearance from vehicle to vehicle, all have the same basic meaning: There's a problem with the car's emissions system. The on-board diagnostics system P0C03 and engine control unit are in charge of monitoring a bunch of different aux heater start counter overrun/system locked (same as below ?), and if they get a reading that's a little out of whack, up pops the check engine light.

Difficulty Level (Soso)

Repair Time (50 Min.)

Cost Prediction : $ 40-75

Common Causes of Bristol 404 P0C03 OBD2 Code

A common cause of code P0C03 is the failure of Aux Heater Start Counter Overrun/System Locked (same as below ?), but there are several other possible causes as well, such as ;

• Air fuel ratio (A/F) Sensor 1 Bank 1 circuit poor electrical connection
• Dirty Oil
• Faulty Crankshaft Position Sensor (POS)
• Intake Valve Timing Control Solenoid Valve circuit poor electrical connection

P0C03 is a kind of Powertrain Trouble Code Powertrain of a modern automobile, comprising engine (with exhaust system), transmission, drive shaft, suspension and the wheels. In a motor vehicle, the term powertrain or powerplant describes the main components that generate power and deliver it to the road surface, water, or air.

P0C03 code for other Bristol cars

You can view according P0C03 DTC for your car model. We selected several models to see obd2 solutions click and view it.

• P0C03 Briscoe Cloverleaf
• P0C03 Bristol 400
• P0C03 Bristol 401
• P0C03 Bristol 402
• P0C03 Bristol 403
• P0C03 Bristol 405
• P0C03 Bristol 406
• P0C03 Bristol 407
• P0C03 Bristol 408
• P0C03 Bristol 409
• P0C03 Bristol 410
• P0C03 Bristol 411
• P0C03 Bristol 412
• P0C03 Bristol 450
• P0C03 Bristol 603
• P0C03 Bristol Beaufighter
• P0C03 Bristol Blenheim
• P0C03 Bristol Brigand
• P0C03 Bristol Britannia
• P0C03 Bristol Fighter

Engine OBD 2 Codes website is a freeware resource center for engine trouble codes.

About Us | Contact | Privacy

Copyright 2017 © All rights reserved