C3198 Bentley Brooklands OBD Code

OBD/2 C3198 error code description and symptoms.

Intake Manifold Runner Control Malfunction (Stuck Open) The IMRC system is monitored for failure during continuous, key ON engine OFF or key ON engine running self-test. The test fails when the signal on the monitor pin is less than an expected calibrated range at closed throttle. IMRC monitor signal circuit shorted to PWR GND or SIG RTN Damaged IMRC actuator Damaged PCM An IMRCM PID reading approximately near 1 volt at closed throttle may indicate a fault.

On some transmissions, such as automated manual transmissions or automatic transmissions with manual mode, the GSP switch lets the TCM know whether or not the driver has selected automatic or manual function. On manual transmissions, the GSP switch informs the TCM which gear the driver is selecting, and may function as a neutral safety switch, depending on system design. The TCM also uses the gate select position switch to monitor transmission operation. For example, if the driver selects manual mode and selects 3rd gear on an automatic transmission, the TCM may monitor speed sensors to detect clutch and brake slippage.

C3198 Bentley Brooklands Error Code Repair Process :

If your seat rear up/down potentiometer feedback circuit short to ground check engine light is illuminated, it's best to take it in for diagnostic testing, which can feel like a hassle. Because while the lights vary in appearance from vehicle to vehicle, all have the same basic meaning: There's a problem with the car's emissions system. The on-board diagnostics system C3198 and engine control unit are in charge of monitoring a bunch of different seat rear up/down potentiometer feedback circuit short to ground, and if they get a reading that's a little out of whack, up pops the check engine light.

Difficulty Level (Expert)

Repair Time (60 Min.)

Cost Prediction : $ 80-120

Common Causes of Bentley Brooklands C3198 OBD2 Code

A common cause of code C3198 is the failure of Seat Rear Up/Down Potentiometer Feedback Circuit Short To Ground, but there are several other possible causes as well, such as ;

• 1Camshaft Position Sensor circuit poor electrical connection
• EVAP system hose leaking
• Faulty Fuel injector
• Variable Camshaft Timing (VCT) position circuit is open or shorted

C3198 is a kind of Chassis Trouble Code Diagnosing chassis noises can be one of the most frustrating problems technicians face. Fortunately, manufacturers have engineered noise, vibration and harshness (NVH) diagnostic techniques and equipment to find the source of the noise.

C3198 code for other Bentley cars

You can view according C3198 DTC for your car model. We selected several models to see obd2 solutions click and view it.

• C3198 Bentley 3.5-litre
• C3198 Bentley 3-litre
• C3198 Bentley 4.25-litre
• C3198 Bentley 4.5-litre
• C3198 Bentley 4-litre
• C3198 Bentley 6.5-litre
• C3198 Bentley 8-litre
• C3198 Bentley Arnage
• C3198 Bentley Azure
• C3198 Bentley Continental
• C3198 Bentley Continental Gt
• C3198 Bentley Exp
• C3198 Bentley Hunaudieres
• C3198 Bentley Java
• C3198 Bentley Mark V
• C3198 Bentley Mark Vi
• C3198 Bentley Mulsanne
• C3198 Bentley R-type
• C3198 Bentley S1
• C3198 Bentley S2
• C3198 Bentley S3
• C3198 Bentley Speed
• C3198 Bentley State
• C3198 Bentley T
• C3198 Bentley Turbo

Engine OBD 2 Codes website is a freeware resource center for engine trouble codes.

About Us | Contact | Privacy

Copyright 2017 © All rights reserved