C0550 Pininfarina Eta OBD Code

OBD/2 C0550 error code description and symptoms.

EGR Flow Insufficient Detected The EGR system is monitored during steady state driving conditions while the EGR is commanded on.
The test fails when the signal from the DPF EGR sensor indicates that EGR flow is less than the desired minimum. Vacuum supply EGR valve stuck closed EGR valve leaks vacuum EGR flow path restricted EGRVR circuit shorted to PWR VREF open to D.P.F. EGR sensor D.P.F. EGR sensor downstream hose off or plugged EGRVR circuit open to PCM VPWR open to EGRVR solenoid D.P.F. EGR sensor hoses both off D.P.F. EGR sensor hoses reversed Damaged EGR orifice tube Damaged EGRVR solenoid Damaged PCM Perform KOER self-test and look for DTC C0550 as an indication of a hard fault.

To check for an open circuit, trace along the length of the transmission control circuit, checking for breaks in the wiring. Repair any broken wiring and make sure all connectors are fully seated and locked.Pay close attention to connectors, looking for corrosion, bent or broken pins, or moisture in the connector. Repair any connector issues even if they are not specifically part of the transmission control circuit as they may serve a function in providing power to the transmission control circuit.

C0550 Pininfarina Eta Error Code Repair Process :

The rule of C0550 code when it comes to emissions-related vehicle repair is that any modification that changes the vehicle from a certified configuration to a non-certified configuration is considered tampering: this applies to both vehicle owners and repair facilities and is, therefore, a Federal offense. Replacing a catalyst with a straight pipe is one traditional example of seat horizontal motor memory position out of range. Likewise, overriding the OBD C0550 error in system through the use of high-tech defeat devices or non-certified computer chips, for example, would also be considered tampering. The OBD system may, however, be repaired back to its original certified configuration with certified performance chips or appropriate aftermarket parts.

Difficulty Level (Soso)

Repair Time (50 Min.)

Cost Prediction : $ 60-110

Common Causes of Pininfarina Eta C0550 OBD2 Code

A common cause of code C0550 is the failure of Seat Horizontal Motor Memory Position Out of Range, but there are several other possible causes as well, such as ;

• Air fuel ratio (A/F) Sensor 1 Bank 1 circuit poor electrical connection
• Damaged camshaft position (CMP) sensor
• Fuel pressure
• Continuous oil flow to the VCT piston chamber

C0550 is a kind of Chassis Trouble Code Diagnosing chassis noises can be one of the most frustrating problems technicians face. Fortunately, manufacturers have engineered noise, vibration and harshness (NVH) diagnostic techniques and equipment to find the source of the noise.

C0550 code for other Pininfarina cars

You can view according C0550 DTC for your car model. We selected several models to see obd2 solutions click and view it.

• C0550 Pininfarina 33
• C0550 Pininfarina Argento
• C0550 Pininfarina Birdcage
• C0550 Pininfarina Blmc
• C0550 Pininfarina Chronos
• C0550 Pininfarina Corvette
• C0550 Pininfarina Coupe
• C0550 Pininfarina Enjoy
• C0550 Pininfarina Ethos
• C0550 Pininfarina Hit
• C0550 Pininfarina Metrocubo
• C0550 Pininfarina Mythos
• C0550 Pininfarina Osee
• C0550 Pininfarina Rossa
• C0550 Pininfarina Rosso
• C0550 Pininfarina Spider
• C0550 Pininfarina Start

Engine OBD 2 Codes website is a freeware resource center for engine trouble codes.

About Us | Contact | Privacy

Copyright 2017 © All rights reserved