B0145 Simca 1500 OBD Code

OBD/2 B0145 error code description and symptoms.

Output Shaft Speed sensor circuit intermittent failure The output shaft speed sensor signal to the PCM is irregular or interrupted.
Harness connector not properly seated Harness intermittently shorted, or open Harness connector damaged OSS sensor damaged, or not installed properly Verify harness and connector integrity Verify OSS sensor proper installation.

Gear changes are accomplished by a command from the TCM to energize the clutch actuator to release the clutch; after which various actuators inside the transmission disengage the current gear, and depending on current operating conditions, engage the next higher or lower gear ratio. All of this happens much faster than a human driver could change gears, and in most applications, gear changes are as smooth and seamless as on any fully automatic transmission.

B0145 Simca 1500 Error Code Repair Process :

If your vehicle failed a B0145 test and the B0145 Check Engine Light is NOT on, chances are you have a problem with the OBDII system, a burned out MIL lamp, or a faulty catalytic converter. The converter is essentially an afterburner that cleans up the exhaust after it exits the engine. The OBDII system uses knock sensor 1 circuit intermittent (bank 1 or single sensor) a ownstream oxygen sensor to monitor the efficiency of the converter, and it should detect a drop in converter efficiency if the converter has been contaminated or is failing (ignition misfiring, leaky exhaust valves, and oil burning can all damage the converter). What you want to look knock sensor 1 circuit intermittent (bank 1 or single sensor): Any conditions that might cause ignition misfire, an overly rich or lean fuel condition, or loss of compression. Use your OBD Express DIY to look at the oxygen sensor outputs, coolant temperature, airflow, calculated engine load, and inlet air temperature.

Difficulty Level (Expert)

Repair Time (35 Min.)

Cost Prediction : $ 20-50

Common Causes of Simca 1500 B0145 OBD2 Code

A common cause of code B0145 is the failure of Knock Sensor 1 Circuit Intermittent (Bank 1 or Single Sensor), but there are several other possible causes as well, such as ;

• Camshaft Position Sensor harness is open or shorted
• Camshaft advance mechanism binding (VCT unit)
• Fuel injectors may be faulty
• Incorrect fuel filler cap used

B0145 is a kind of Body Trouble Code Auto body problems aren't always easy to spot. Diagnosing auto body problems sometimes requires a little know-how. In this section you'll find articles dedicated to teaching you how to diagnose auto body problems.

B0145 code for other Simca cars

You can view according B0145 DTC for your car model. We selected several models to see obd2 solutions click and view it.

• B0145 Simca 1000
• B0145 Simca 11
• B0145 Simca 1100
• B0145 Simca 1200
• B0145 Simca 1300
• B0145 Simca 1301
• B0145 Simca 1307
• B0145 Simca 1308
• B0145 Simca 1309
• B0145 Simca 1501
• B0145 Simca 2 Litres
• B0145 Simca 5
• B0145 Simca 6
• B0145 Simca 8
• B0145 Simca Ariane
• B0145 Simca Aronde
• B0145 Simca Horizon
• B0145 Simca Montlhery
• B0145 Simca Oceane
• B0145 Simca Plein
• B0145 Simca Plein Ceil
• B0145 Simca Tufao
• B0145 Simca Type 11
• B0145 Simca Vedette
• B0145 Simca Vedette Beaulieu
• B0145 Simca Vedette Marly
• B0145 Simca Vedette Versailles

Engine OBD 2 Codes website is a freeware resource center for engine trouble codes.

About Us | Contact | Privacy

Copyright 2017 © All rights reserved